Відео

Did you cut the tube at the end? It looks shorter…

Saved me a huge headache, much props!

My start relay got busted, and I opened it for fun. Can anyone explain to me what the round disk (at 3:54) is and what does it do? Because I decided to peek inside the starter relay for fun and found the disc and I'm not familiar with its use. Thanks in advance. :)

Learn how to test if your fan motor is bad here: ua-cam.com/video/x9fK0bN72MA/v-deo.html

Clear, concise, and to the point. Nicely done and thanks for saving me from calling someone.

Its sad that whirpool knows there is a huge issue in their dryer timer knobs and they dont replace it if ur warranty is out.

Do you know how can I signature a program ?

Even though mine is deactivated i still can't adjust the temperature. Is that normal?

Changed all 4 thermistors, all fans are running, condenser is cleaned.compressor is running. Freezer will not get below 29°F. Another not the 10 awg is too small it will strip all conductors. It should only be used to score the conductor cover.

Did it move when you took the tape off?

Woo so many user suffering same issues 😢

THE BEST! FIXED IT. Thank you so much!!!!

My GE ice maker is not filling. Replaced the icemaker, didn't fix it. Replaced the dual water valve, didn't fix it. Your video was helpful in this. What else can I try? The water dispenser is working, but no luck getting water into the ice maker.

Great tutorial. He spoke very calmly and slowly. The lighting was excellent so you could see exactly what he was doing.

All 5 of my led lights are dimmed. Do they all need to be replaced? Or might it be a separate issue?

very concise and compete repair video. I will order the relay control board since that looks like the problem with the F9 error code. I replaced it approximately a year ago but it didn't last very long.

Great video, thanks for the help!

As soon as i install the new water pump it burns. Why? (I got the right part)

I emptied my ice maker and later went back for more ice and it had not produced anymore. I tried resetting and still no ice. I also removed the water filter and reinstalled the same filter because I’m not due to buy another filter until November. Do you have a solution to my situation?

I got the fridge reading the chip finally but yes it stores the old info so my new filter shows 3%. i'm fine just marking my calendar for replacement if when its down to zero it doesn't lock you out. Anyone know ??

Please help. My thermostat is showing continuity at room temp. Bought a new one and the new one is doing the same. I have a 55-5304521781 frodgidair. Thermostats has FR-5 57/43 on it. Evap coils keep freezing over. Heater has continuity and measuring 30+ olms

It would’ve been nice if you showed us where to find this component. Lol.

I replaced the part and I'm getting the error code please help

The new part is bigger than the original. Probably to make is stronger. FYI you must trim about a match width of each end of the spring or it will not work properly and make a popping noise when closed. Your welcome!

Thanks, good clear video. My problem is not the cover assembly but how to remove the lever assembly behind the cover assembly #DA97-12675T. Thanks for any help

Learn how to replace the timer here: ua-cam.com/video/vSvJVR2tCB8/v-deo.html

Would a faulty evaporator fan motor also cause the ice maker to not make ice?

Fixed my Samsung washer thanks to this video. Very well explained how to remove old and install new. The only thing missing was explaining how to remove the round turning knob. Otherwise great video and saved me hundreds of dollars.

Excellent video! Also, Samsung’s ice maker design is terrible. I will buy any other brand first before buying another Samsung.

But what if the shaft broke off with the knob?

Thanks for sharing.....not sure of someone asked this but is it fine if I tilt it? Moving mine from the kitchen to the garage. Not laying it down, just tipping it.

What do you do if thr retainer breaks off?

Do u have video for the bottom ice maker replacement no error code so I’ll take a chance on it being the ice maker same model as this I already did top it’s garbage I keep it off I’ll prob buy different fridge not a Samsung but would like to swap out maker

Thank You !

We tried this and it made it worse :( can’t set the clock or even preheat the oven. Any advice???

Learn how to check your washer for error codes here: ua-cam.com/video/wMfaFhZOaU0/v-deo.html

Learn how to test the reed switches using magnets here: ua-cam.com/video/F76qOqyYOqY/v-deo.html

Our older french door Samsung will only turn the interior light on when the left door is opened. The right door does not trigger the light. So we know the bulbs work. Is it likely a reed switch for the right door? Will one switch being bad affect the cooling/fan?

Is there another fan in the freezer of this model? The sound we heard of a fan hitting ice sounded like it was coming from the lower compartment. Thank you.

👍

Great video! I recently replaced the broil element on my LG LRE30453ST Oven (Thanks PartsDr!). Yesterday, I was baking and the food remained uncooked, after the display showed 330 degrees for 45 min. I had set it to 350. After removing the cover, checking the bake & broil elements, this is what I found: The bake element turns on (230V) for about 7-8 seconds and turns off. The broil element turns red hot whenever the bake element is off, and after about 2-3 mins, it repeats this cycle. The temperature is probably correct, since the temp sensor is near the top beside the broil element. Since the elements appear to work fine, I though of the control board, but I am getting no errors on the display at all. Any thoughts?

My water line is on the bottom. Is it also connected with a clip?

Respectfully request your assistance or tip: I can't get the plastic air tunnel to lock in place. Im pushing it up but there seems to be some resistance. The coil looks to be in place correctly. Thanks for video.

Thanks for your video. You don`t muck around with unnecessary small talk, which is important as to stay focused on the job at hand. P.S. I have learned to take video snap-shots as you suggest, as I like to once a year carefully disassemble my appliances to either clean, repair or replace out worn parts, ie dehumidifier, etc, etc. thanks again.

THANK YOU for such a simple & user friendly video!!! 🌟

After descaling my Keurig descale light stays on

looks like the black jumper wire's crimp corroded over the past 13 years and killed my fuse. Thanks to your video I found out that everything else is OK. Gotta get a new wire and fuse now.

Does polarity on a thermostat matter? What happens if you switch the wires?

Successfully completed job! Thank you for the help!!!

Thanks very much for the video - good info. But I'd sure think there would be a better way to ship a gasket than the current method where a person has to massage and work with the new gasket for up to a couple weeks. Wow. (OK - I see comments below about a bathtub with hot water - yeah that sounds much easier.)